Shimano reel handle replacement Guide

Shimano reel handle replacement Guide

Our Gomexus Reel Handle Replacement Guide will teach you how to remove and replace the handle knob of a fishing reel handle. Keep reading.

If you want to replace your fishing reel handle, our Gomexus reel handle replacement guide is all you need to get the job done.

Fishing enthusiasts always have a special connection with their fishing equipment, and the reel is one of the most crucial parts of that equipment. Shimano is a well-known brand in the fishing industry and is widely recognized for its high-quality reels. However, like any other machinery, Shimano reels are prone to wear and tear over time. Therefore, it's important to know how to replace a Shimano reel handle. 

In this article, we will teach you how to replace your handle knob of Shimano reels and also provide a step-by-step tutorial for installing a Shimano reel handle.

Shimano Reel Introduction

Shimano produces a wide range of fishing reels for different types of fishing, including spinning, baitcasting, and offshore fishing reels. Shimano's reels are popular among both professional and recreational anglers for their durability, performance, and reliability.

Shimano Reel Introduction

Reel Handle Introduction

The reel handle is one of the most crucial parts of a fishing reel. It's the part that you hold onto while you're reeling in your catch. Over time, the handle knob of the reel can become worn out or damaged, and it needs to be replaced. In addition, anglers may want to customize their fishing gear or match the handle with the rod they are using.

Reel Handle Introduction

Handle Knob Removal Tutorial for Shimano Reels

Before you can install a new handle knob, you need to remove the old one. Here's a step-by-step tutorial on how to remove the handle knob of a Shimano reel:

Step 1: Remove the Retainer Screw

The first step is to remove the retainer screw that holds the handle knob in place. To do this, use a screwdriver to turn the retainer screw counterclockwise until it comes loose. Be careful not to lose the screw as you remove it.

Step 2: Remove the Handle Nut

Next, remove the handle nut. The handle nut is the circular piece that sits underneath the handle knob. Use a wrench or pliers to turn the handle nut counterclockwise until it comes loose. Again, be careful not to lose the nut as you remove it.

Step 3: Remove the Handle Knob

Once you've removed the handle nut, remove the handle knob. Simply pull the handle knob away from the reel's body, and it should come off easily.

Step 4: Remove the Handle Arm

If you need to replace the handle arm as well, you'll need to remove it at this point. To do this, use a wrench or pliers to turn the handle arm counterclockwise until it comes loose. Then, pull the handle arm away from the reel's body.

Step 5: Clean the Reel Handle

Before you install the new handle knob, take some time to clean the reel handle. You can use a soft cloth and some warm soapy water to clean the handle and remove any dirt or debris.

Step 6: Inspect the Reel Handle

While you're cleaning the reel handle, take the time to inspect it for any signs of wear and tear. If you notice any damage, it's best to replace the handle arm as well.

Handle Knob Tutorial for Installing a Shimano Reel

Once you've removed the old handle knob, it's time to install the new one. Here's a step-by-step tutorial on how to install a new handle knob on a Shimano reel.

Step 1: Install the Handle Arm (if necessary)

If you need to replace the handle arm, start by inserting the new handle arm into the reel's body. Make sure that the handle arm is aligned properly with the reel's gear before you tighten it.

Step 2: Install the Handle Knob

Next, slide the new handle knob onto the reel's handle arm. Make sure that the handle knob is seated properly on the handle arm.

Step 3: Install the Handle Nut

After you've installed the handle knob, it's time to install the handle nut. Place the handle nut over the handle arm and thread it onto the reel's body. Use a wrench or pliers to tighten the handle nut clockwise until it's snug.

Step 4: Install the Retainer Screw

The final step is to install the retainer screw. Insert the retainer screw into the hole on the side of the handle knob and tighten it clockwise with a screwdriver until it's snug.

Step 5: Test the Handle

Once you've installed the new handle knob, give it a quick test to make sure it's working properly. Turn the handle to see if it spins smoothly and without any resistance.

Step 6: Lubricate the Reel Handle

Finally, it's important to lubricate the reel handle to ensure that it operates smoothly. Apply a small amount of reel oil or grease to the handle and turn it several times to distribute the lubricant evenly.

Conclusion

Replacing the handle knob of a Shimano reel is a simple process that can be done in just a few minutes with the right tools and a little know-how. This guide will enable you to easily remove and install a new handle knob on your Shimano reel.